搜索资源列表
i2c_master
- i2c 主机代码 可综合,通过fpga验证-I2C master code
I2C
- 基于verilog的I2C代码,包含master和slave两个模块-Verilog-based I2C code that contains the master and slave two modules
i2c_master
- I2C master模式的IP core(verilog)-I2C master mode IP core (verilog)
pic18i2c
- pic的i2c模块主控例子,基于中断方式完成,适用于PIC18系列-pic module i2c master an example based on the completion of the interrupt for the PIC18 series
i2c
- ARM-M0-LPC1114 I2C串口通讯程序-From device to device, the I2C communication protocol may vary, in the example below, the protocol uses repeated start to read data from or write to the device: For master read: the sequence is: STA,Addr(W),offset,RE-
i2c-ina-master
- i2c program for pic24h
I2C
- 自己学习时写的,实现了以单片机作为主机的I2C单用户系统。只限于功能仿真,完成协议的要求。-This project is determined to realize the I2C protocol in which a MCU is the master.
LINUX-i2c
- 在LINUX系统中进行I2C总线的传输,通过本例程了解串口的基本原理及使用 ,理解并掌握对串口进行初始化 * * * * 2.请使用串口调试助手(Baud 4800、数据位8、停止位1、效验位无)做为上位机来做收发试验。在调试助手字符串输入框中输入数字和字符,按发送按钮,然后观察接受窗口的变化。也可以用调试助手自动循环发送。 -I2C bus transfer in LINUX system to understand the the se
i2c-designware
- Synopsys DesignWare I2C adapter driver (master only).
Nios-II-I2C
- 使用开源的IIC MASTER Core,将它加载到NIOSII的AVALON总线上,这样对于NIOSII控制器而言,IIC MASTER就是一个硬件实现的控制器,用户通过调用API函数就能很容易的对IIC进行操作,而且IIC的运行并不占用NIOSII软核宝贵的资源和时间。 -Open source IIC MASTER Core,it is loaded into the AVALON bus NIOSII This NIOSII controller,IIC MASTER is a hard
i2c
- I2C作为master的源码,与AMBA中的AHB兼容。-I2C compatible with the AMBA AHB master source.
实例模块
- 各种加法器/计数器、乘法器/除法器、编码器/译码器、状态机、SPIMaster Controller、I2C Master controller、CAN ProtocolController、Memory模块、JPEG图像压缩模块、加密模块、ATA控制器、8位RISC-CPU等及各个实例模块相应的Testbench
CORTEX-M0-I2C
- arm cortex M0 的I2C接口的例程,包括主口和从口都有 -arm cortex m0 s examples for I2C ,including master and slave
I2C_master_rx_multi_int
- program for I2C master multi RX
I2C_SoloMaster_Controler_02
- 本模块是通用的I2C Master控制器。 它支持3种模式:单纯写N次,单纯读N次,先写一次,然后读N次。 本模块的读写只是从I2C的角度,因此,对所有的DataIn, 本模块均当成传送的数据,具体在Slave那边的定义,由上层模块处理。-I2C Master
PIC_CODE
- PIC单片机I2C主从通讯,使用硬件I2C接口.-PIC microcontroller I2C master-slave communications, hardware I2C interface.
C8051F120-I2C-simulate
- C8051F12x 主机模式 模拟SMBus -Example software to demonstrate the C8051F12x SMBus interface in Master mode.
i2c_master_slave_latest.tar
- I2C master slave 代码,非常有用,可以参考-I2C master slave code, very useful, you can refer! ! !
I2C
- 4. I2C程序设计与电路仿真 LPC2138微控制器具有标准的硬件I2C接口,可配置主机或从机,总线时钟频率可调整,可支持400KHZ总线频率。使用I2C总线时,要将P0.2、P0.3连接设置选择SCL、SDA,并且总线上要接两个上拉电阻,阻值1~5千欧。 定义器件的地址和LED输出端口,设置包括从机地址、子地址、数据缓冲区指针、操作数据个数、操作结束标志、子地址使能控制在内的变量。使用PINSEL0、PINSEL1寄存器设置I/O口工作模式,设置LED控制口为输出,其他I/O为输入。
I2C_MODULE
- I2C 主机外设 可以配置100K到1MHz I2C通信 可以配置不同长度,读 或些 I2C通信。-I2C master